Short answers first, details after. If your question isn't here, put it in the notes on the waitlist form.
When will the kiln open?
Not yet. The kiln is planned and not installed, and we aren't taking in wood. The homepage carries a dated status line that we update every month.
Join the waitlist and you'll hear from us before the first loads are booked.
What will it cost?
We haven't set our rates. For comparison, kilns elsewhere post roughly a dollar to two dollars a board foot for stock up to 2 inches, and often bill thicker wood by time in the kiln. Our cost page lists those posted rates and has an estimator.
Is there a minimum load?
Expect one. Posted minimums at other US kilns run about $100 to $150 a load. A small batch can still make sense if you pair up with another woodworker whose wood matches yours in species and thickness.
Do I need to air-dry my wood first?
Not always, but it usually pays. A kiln can dry lumber straight from the saw, but green wood takes several times longer: the USDA Forest Products Laboratory lists at least 23 days for green 4/4 white oak against 5 days for air-dried. Under time-based pricing, that difference is money. For thick stock and oak, air drying under a roof first also takes the riskiest stage out of the kiln. Our air drying guide shows how.
Can you dry 3-inch slabs?
Not yet, since the kiln isn't built. Three-inch slabs can be kiln-dried, slowly: FPL's thickness factors put 12/4 stock at more than four times the drying time of 4/4, and thick slabs need gentle schedules to avoid honeycomb. Most do best air-dried for a long time first, then finished in a kiln. See drying thick slabs.
How long will my wood be in the kiln?
Roughly a week for air-dried 1-inch hardwood, and two to three weeks for 2-inch, based on FPL's minimum kiln times plus the extra it says real loads take. Green wood, white oak and thick slabs all take longer. Our drying times page breaks it down by species and thickness.
Will kiln drying change the color of my wood?
It can, a little. FPL expects some darkening of hard maple and ash in the kiln. Pale woods keep their color best when drying starts fast and not too hot, and they gray or stain when they sit wet and warm. Walnut is the opposite case: some woodworkers steam it before drying on purpose, to darken the pale sapwood. See drying maple and drying black walnut.
Will kiln drying crack my wood?
A well-run kiln shouldn't add cracks. Checks form when wood dries too fast, mostly early in drying, and kiln schedules exist to keep the drying rate below each species' safe limit. Two caveats: cracks already in the wood can reopen as it dries, and slabs that include the pith often split from it however carefully they're dried. The causes are covered in what goes wrong in a kiln.
Does kiln drying kill bugs?
Yes, as long as the center of every piece gets hot enough for long enough; a few hours at 130°F or more does it, and normal steam and dehumidification schedules get there. Wood can pick up new beetles later, so finish it or keep it indoors. See lumber sterilization.
What's the difference between kiln-dried and air-dried?
Mostly how dry it ends up. In G5507, MU Extension gives 12 to 14 percent as typical for Missouri air-dried lumber, and 6 to 10 percent for wood indoors; furniture lumber is usually kiln-dried to 6 to 8. A kiln also kills insects and, run properly, relieves drying stress. See kiln-dried vs air-dried.
Can you dry firewood?
Not yet. We don't plan to dry firewood; our plans center on lumber and slabs.
Firewood is a different load from lumber: it's dried for burning, not for building, and it's piled rather than stickered. If you're asking because of emerald ash borer, note that the USDA treatment the Wood Handbook cites for that pest is stricter than ordinary heat treatment: 140°F at the core for at least 60 minutes.
Where can I get wood dried today?
Not from us yet. Some ways to find a kiln in the meantime:
- Ask sawmills in the area. Some may run a kiln or know who does.
- Ask woodworking clubs and guilds. Members may know who dries custom loads.
- Contact your county MU Extension office. MU publishes the drying guides we cite on this site, and extension staff may know of kilns nearby.
- Build a small solar kiln. FPL's drying manual includes plans for one sized for a few hundred board feet; see our kiln types guide.
Meanwhile, stack and cover your wood properly so it's in good shape when a kiln is available.
How do I figure out how many board feet I have?
Multiply length in inches by width in inches by thickness in inches, and divide by 144. A board 8 feet long, 8 inches wide and 1 inch thick is 96 × 8 × 1 ÷ 144 = 5.33 board feet. Our guide to board feet for a drying load covers slabs, beams and whole stacks.
What moisture content should I aim for?
For furniture, cabinets and flooring in Missouri, 6 to 8 percent is a good target; MU's indoor range is 6 to 10. Barns and garages are fine at 15 to 20 percent. See moisture content targets.
Join the Waitlist
Still have a question about your wood? Ask it in the notes on the waitlist form.