COLUMBIA
KILN DRYING
Join the Waitlist

Status · November 15, 2026: planned, not installed. We are not accepting wood.

Drying Missouri Hardwoods, Species by Species

White oak is the slowest and most check-prone of the common Missouri hardwoods. Red oak and hickory come next. Walnut, cherry and hard maple dry at a moderate pace, and ash and soft maple give up water fastest. Each one also has its own way of going wrong: white oak checks and honeycombs, walnut needs care with its pale sapwood, maple stains if it dries too slowly, and ash draws powderpost beetles.

The table puts the numbers side by side. The species pages explain what to do about them.

The common Missouri hardwoods, compared

Species Green moisture content, heartwood / sapwood Safe drying rate, 4/4 (% per day) Kiln days, 4/4 from air-dried / green Watch for
White oak 64% / 78% 2.5 5 / 23 Surface checks, honeycomb
Red oak (northern) 80% / 69% 3.8 5 / 21 Surface checks, honeycomb
Hickory Varies by species Not listed 4 / 10 Sapwood stain, powderpost beetles
Black walnut 90% / 73% 8.2 5 / 11 End checks; pale sapwood
Cherry 58% heartwood 5.8 5 / 10 Few; honeycomb in wetwood (not common)
Hard (sugar) maple 65% / 72% 6.5 5 / 11 Sticker stain, gray sapwood stain
Soft maple (silver) 58% / 97% 13.8 (sapwood) 4 / 7 Sapwood stain if dried slowly
White ash 46% / 44% 10.4 4 / 10 Gray-brown sapwood stain, powderpost beetles

Sources: green moisture content from the Wood Handbook, ch. 4, Table 4–1; safe drying rates and minimum kiln days (to 6 percent in conventional kilns) from FPL-GTR-118, Tables 8.6 and 7.25.

Two things in that table surprise people. First, wetter isn't slower: walnut heartwood starts out far wetter than white oak heartwood but dries much faster, because white oak's pores are plugged. Second, the gap between "from air-dried" and "from green" is biggest for the oaks. Air-drying oak before the kiln saves the most time.

Easy, moderate and hard to dry

FPL's drying manual sorts hardwoods into three groups for choosing a drying method. Oak and beech are its examples of hard-to-dry species; hickory and hard maple are moderately hard; ash, basswood, yellow-poplar and soft maple are easy. The hard-to-dry group gains the most from a careful start, under a roof or in a predryer, before the kiln. The easy group gains the most from speed, because its risk is stain, not cracking.

White oak

The slowest common hardwood, held to the gentlest kiln schedules. Its heartwood pores are blocked by growths called tyloses, so water leaves slowly, and the surface checks if it's pushed. Air-dry it under a roof and give it extra time at every thickness. Drying white oak

Black walnut

Moderate and fairly forgiving, but thick walnut can end-check and honeycomb, and its pale sapwood contrasts with the dark heartwood. Steaming before drying is the usual way to even out the color. Drying black walnut

Maple

Hard maple dries at a moderate rate; soft maple is fast. Both are prized for pale wood, and both stain if they dry too slowly at warm temperatures: gray sapwood stain, and sticker stain that shows only after planing. Speed and airflow are the cure. Drying maple

Ash

Low green moisture content and a fast safe drying rate make ash one of the easiest Missouri hardwoods to dry. The catches are gray-brown sapwood stain if it sits wet, and powderpost beetles, which favor large-pored hardwoods like ash. Drying ash

Mixing species in one load

Kilns run one schedule for the whole chamber, so a load is only as fast as its slowest board. FPL's manual advises drying one species at a time, or a few with similar drying characteristics. White oak can't share a schedule with ash or soft maple without either slowing them down or risking checks in the oak. That's why kiln loads are grouped by species and thickness.

For general timelines, see drying times. For the target number at the end, see moisture content.

Join the Waitlist

Tell us which species you have and how thick. A waitlist heavy in white oak needs a different kiln plan from one full of ash.

Join the Waitlist

HELP SHAPE THE PLANNED KILN

What wood would
you bring?

Share your species, thickness and board feet. We’ll email you before the kiln opens.

Join the Waitlist