Heat kills powderpost beetles, borers and their eggs when the center of every piece reaches the right temperature and stays there. The USDA Forest Products Laboratory's drying manual says thoroughly heating wood to 130°F or more kills all existing insects, their eggs and any associated fungi. The international standard for wood packaging, ISPM 15, requires a core temperature of 133°F (56°C) held for at least 30 minutes (Wood Handbook, ch. 20). Air drying never does this, however long the wood sits.
The catch is the word "core." The air in a chamber gets hot quickly; the middle of a thick beam takes hours.
Signs of powderpost beetles
Powderpost beetle larvae tunnel inside the wood for months to years, then chew their way out as adults. What you see:
- Small round exit holes. Oklahoma State University Extension describes lyctid exit holes as 1/32 to 1/16 inch across (OSU Extension).
- Fine powder. OSU calls it flour- or talc-like. It packs the tunnels and sifts out of exit holes and cracks onto whatever is underneath.
- Little piles under a board or on the floor. Clean them up. If powder reappears in the same spots, something is still active.
OSU says the life cycle usually runs three months to a year but can take several years, depending on species, temperature and the starch content of the wood. Holes in a board tell you beetles were there; fresh powder tells you they still are.
Why air-dried and barn wood carry bugs
Because that's where the beetles get in. OSU says most infestations are in wood before it's ever bought, and that farm-sawed lumber is often the source.
Air-drying conditions suit them. FPL notes that the best conditions for insect damage during drying are between 80°F and 100°F, a typical Missouri summer. FPL also points to the yard itself: piles of slabs, sawdust, bark, old lumber and sticker scraps are breeding grounds, and cleaning them up removes most insect problems (FPL-GTR-118).
And drying doesn't make wood immune. FPL notes that while few insects will invade wood below 10 percent moisture content, lyctid powderpost beetles are one of the three that do, along with termites and carpenter bees.
The temperature and time that kill them
Four published guidelines, all close together:
| Source | Requirement |
|---|---|
| ISPM 15, international standard for wood packaging | Core at 133°F (56°C) for at least 30 minutes |
| FPL drying manual, research summary | Wood thoroughly heated to 130°F or more kills insects, eggs and fungi |
| FPL drying manual, US and Canadian kiln sterilization practice | Center of all lumber in the kiln at 133°F for at least 6 hours |
| Oklahoma State University Extension | Kiln-dried at 130°F to 140°F and 80% relative humidity, at least 8 hours |
Sources: Wood Handbook, ch. 20; FPL-GTR-118; OSU Extension.
Some pests need more. For emerald ash borer, the Wood Handbook cites a USDA requirement of 140°F at the core for 60 minutes or longer, and its table of pests that ISPM 15 heat treatment controls lists lyctid beetles "with some exceptions."
How long it takes to heat the core. FPL tested hardwood pieces in a 160°F chamber with saturated air. Red oak reached 133°F at the center in about:
| Piece size (actual, inches) | Saturated air | Air 10°F below saturation |
|---|---|---|
| 1 × 6 | 14 minutes | 15 minutes |
| 2 × 6 | 49 minutes | 56 minutes |
| 4 × 4 | 109 minutes | 124 minutes |
| 6 × 6 | 252 minutes | 284 minutes |
Source: Wood Handbook, Table 20–4. Times then add the 30 minutes or more at temperature.
Three lessons from that research:
- Thickness rules. A 6x6 takes about 18 times as long to heat through as a 1x6.
- Humid heat is faster. Dry air cools the wood surface as water evaporates, so heating slows. FPL found heating times grew sharply as the air got drier.
- Sticker it. The Wood Handbook says a solid bundle of 1x6 lumber takes at least 10 times longer to heat than the same wood stickered.
That's why serious sterilization measures temperature inside the wood, in the slowest, coolest spot in the chamber, rather than trusting the air. FPL says standard schedules in steam and dehumidification kilns achieve sterilization without special steps, but that some older dehumidification kilns need care to reach and hold the temperature.
Ash, hickory, oak sapwood and walnut sapwood
The beetles go where the food is. OSU says the southern lyctus beetle attacks only large-pored hardwoods and most often infests ash, hickory and oak.
Heartwood is less inviting in some species. FPL notes that the dark heartwood of white oak and walnut resists decay and insects. So in a walnut slab, the pale sapwood along the live edge is the part to watch. Ash, a favorite of lyctid beetles, deserves extra care; see drying ash.
Sterilizing reclaimed and barn lumber
Old barn boards and beams are the classic carrier: they've sat for decades in exactly the conditions beetles like. Before any of it comes into a house:
- Look for fresh powder, especially under beams and along joints. Old holes with no powder may be long dead; fresh powder isn't.
- Keep suspect wood out of the house and away from other lumber until it's treated.
- Heat it through. Stickered, with humid heat, until the thickest piece has held at least 133°F at its center.
- Finish it. OSU says most wood-infesting beetles won't reinfest wood that's painted, varnished, waxed or shellacked.
Barn wood has another issue: it's rarely as dry as it looks. See is barn-dried lumber dry enough?
Sterilization on the waitlist
Wood that's already dry doesn't need a full drying run. FPL notes that sterilizing green lumber without drying it takes very humid heat; for wood that's already dry, the job is simply getting the core hot enough and holding it there.
Join the Waitlist
Found holes or powder in your lumber? Tell us the species, how much you have and whether it's already dry.