COLUMBIA
KILN DRYING
Join the Waitlist

Status · November 15, 2026: planned, not installed. We are not accepting wood.

Is Barn-Dried Lumber Dry Enough for Furniture?

Usually not, no matter how many years it's been there. An unheated barn follows the outdoor air, and in Missouri that holds wood somewhere around 12 to 14 percent moisture content. Furniture and cabinets need 6 to 8 percent, and MU Extension's indoor figure for Missouri is 6 to 10 percent (G5507). Barn-stored lumber is a good start, often a great one, but it has a few points left to go before it's ready to build with indoors.

The good news: those last few points are the easy part, if you know where the wood stands.

What "barn-dried" really means

A barn keeps rain and sun off the wood, which matters a lot. It doesn't change the humidity. Inside an open or unheated barn, the wood trades moisture with the same air that's outside.

Given enough time outdoors, the USDA Wood Handbook says, ordinary 1- and 2-inch lumber ends up within a point or two of the local average outdoor equilibrium, and across much of the country the floor for well air-dried lumber is 12 to 15 percent (ch. 13). Its 30-year averages for St. Louis put Missouri's outdoor equilibrium between about 12.3 percent (April) and 14.3 percent (December).

So a board in a Missouri barn won't get much below about 12 percent, and it creeps back up in winter. Ten years in the hayloft won't change that.

Why the last few points matter

Because wood gets smaller as it gives up those points, and it will give them up in your house whether you plan for it or not.

Take a stack of 8-inch-wide, flat-sawn walnut boards from a barn, reading 13 percent. In a heated house they settle near 7. With the Wood Handbook's shrinkage coefficient for black walnut:

8 in × 0.00274 × 6 = about 0.13 in of shrinkage per board.

Glue five of those into a 40-inch tabletop at 13 percent and you're asking it to shrink about ⅔ inch after it's finished. If the top can't move, something cracks. If it can, the breadboard ends stick out or the drawer fronts gap. Either way it happened because the wood was dried in the house instead of before.

Thick stock may not even be barn-dry

Everything above assumes the wood has had time to reach the barn's equilibrium all the way through. Thin boards get there. Thick stock may not.

A slab or beam dries from the outside in, so its core lags behind its surface for years. Woodworkers' usual planning figure is a year of air drying per inch, more for oak. A 3-inch white oak slab stacked four years ago might be barn-dry. One stacked eighteen months ago almost certainly isn't, even if the surface reads 13.

And stacking matters as much as time. Boards piled flat against each other, without stickers, dry very slowly where they touch. Boards on a dirt floor pick up ground moisture. "In the barn for years" describes where the wood was, not how it was stored.

Bugs come with barns

This is the other reason to be careful with barn lumber. Oklahoma State University Extension says most infestations are in wood before it's bought, and names farm-sawed lumber as a common source (OSU Extension).

Look before you bring any of it inside:

  • Small round holes, about 1/32 to 1/16 inch across for lyctid beetles, per OSU.
  • Fine, flour-like powder in the holes, on the boards below, or on the barn floor under the stack.
  • Most often in the sapwood of ash, hickory and oak.

Holes with fresh powder mean live insects. Heating the wood through kills them; see lumber sterilization for the temperatures.

How to check what you have

  1. Pull boards from the middle of the stack, not the top. The middle dries slowest.
  2. Meter them properly, with pins driven well in, and corrected for species and temperature. A cold barn reading needs a temperature correction. Our guide to using a moisture meter on thick stock explains how.
  3. For thick pieces, test the core. Cut a 1-inch section from a cutoff and oven-dry it, or take a deep pin reading.
  4. Look for bugs as above.

If the boards read 12 to 14 percent through and show no insect signs, you have well air-dried lumber that needs one more step.

Ways to finish the job

Kiln dry it. Air-dried lumber goes through a kiln quickly. The USDA Forest Products Laboratory lists about 4 to 5 days as the minimum for air-dried 4/4 Missouri hardwoods in a conventional kiln, against 7 to 23 days from green (FPL-GTR-118). The heat kills insects at the same time. See drying times.

Finish it indoors. For a small amount of 4/4 stock, sticker it in a heated room and meter it every week or two; when the numbers hold steady, it's done. It's slow, it doesn't kill insects, and thick stock may take a very long time, but it works for a few boards.

Leave it as is for the right projects. MU's air-drying guide sets the bar for unheated structures at 15 to 20 percent (G5550), so barn-stored lumber is ready now for sheds, barn repairs, rough benches and outdoor work.

Project Barn-dried as is?
Barn, shed or garage framing and siding Yes
Outdoor benches, planters, rough furniture Usually
Indoor furniture, tabletops, cabinets No: dry to 6–8% first
Flooring and interior trim No: dry to the indoor range first

For more on the difference a kiln makes, see kiln-dried vs air-dried.

Join the Waitlist

Have a barn full of boards waiting for a project? Put the species, thicknesses and rough board feet on the form.

Join the Waitlist

HELP SHAPE THE PLANNED KILN

What wood would
you bring?

Share your species, thickness and board feet. We’ll email you before the kiln opens.

Join the Waitlist