COLUMBIA
KILN DRYING
Join the Waitlist

Status · November 15, 2026: planned, not installed. We are not accepting wood.

Moisture Content Targets for Missouri Woodworking

For furniture, cabinets, flooring and trim used inside a Missouri home, aim for 6 to 10 percent moisture content, and closer to 6 to 8 percent if you're building something glued up and precise. That's the range MU Extension gives for wood in use indoors in Missouri (G5507), and the USDA Wood Handbook recommends an average of 8 percent, with individual pieces between 6 and 10, for interior woodwork across most of the country.

Air-dried lumber won't get there on its own. Here's what to aim for, why, and how to tell where your wood stands.

Target table by use

Use Target moisture content Source
Furniture, cabinets, flooring, interior trim 8% average; individual pieces 6–10% Wood Handbook, Table 13–2
Hardwood lumber dried for furniture, flooring and millwork 6–8% Wood Handbook, ch. 13
Wood in use indoors in Missouri 6–10% MU Extension G5507
Mantels and other thick interior pieces As close to the indoor range as practical Wood Handbook, ch. 13
Exterior siding and trim 12% average; pieces 9–14% Wood Handbook, Table 13–2
Framing lumber 15% average, no more than 19% Wood Handbook, ch. 13
Barns, garages and other unheated buildings 15–20% is adequate MU Extension G5550

Sources: Wood Handbook, ch. 13; MU Extension G5507; MU Extension G5550.

The mantel row needs a word of honesty. The Wood Handbook says drying wood to its in-service moisture content is possible for lumber under 3 inches thick, but seldom practical for solid timbers. A 6x8 beam will keep drying, and shrinking, after it's hung. Our guide on kiln-dried wood for mantels goes into that.

Why air-dried isn't dry enough indoors

Wood trades moisture with the air around it until the two balance. Outdoors in Missouri, that balance sits too high for a heated house: MU's typical figure for air-dried lumber here is 12 to 14 percent, against 6 to 10 indoors.

Those few points are where the trouble lives, because wood shrinks with every point it loses below its fiber saturation point, which MU Extension puts at 25 to 30 percent. The Wood Handbook gives a shrinkage coefficient for each species, and the arithmetic is simple: width × coefficient × change in moisture content.

Take a 12-inch-wide, flat-sawn white oak board going from 12 percent to 7 percent:

12 in × 0.00376 × 5 = 0.23 in of shrinkage across the width.

That's nearly a quarter inch on one board. Glue six of them into a tabletop at 12 percent and the top tries to lose about 1⅓ inches of width once it settles in the house. Quarter-sawn white oak moves about half as much (coefficient 0.00194), and black walnut, flat-sawn, about 0.16 in on the same board (0.00274). The coefficients come from the Wood Handbook's Table 13–5 and hold between 6 and 14 percent.

Equilibrium moisture content through a Missouri year

Equilibrium moisture content (EMC) is the moisture level wood settles at in a given temperature and humidity. Outdoors, Missouri stays humid most of the year. The Wood Handbook's 30-year averages for St. Louis, the Missouri city in its table, show outdoor EMC never falls below about 12 percent:

Month Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec
Outdoor EMC, % 14.2 13.7 13.0 12.3 12.7 12.5 12.5 12.9 13.1 12.8 13.2 14.3

Source: Wood Handbook, Table 13–1.

That's why a stack of boards under a roof, however old, bottoms out around 12 to 14 percent. Indoors is different: heating dries the air in winter and air conditioning pulls moisture out in summer. At 70°F, the Wood Handbook's EMC table gives:

Indoor relative humidity at 70°F 30% 40% 50% 60%
Wood settles at about 6.2% 7.7% 9.2% 11.0%

Source: Wood Handbook, Table 4–2 (ch. 4).

So indoor wood swings a few points between a dry January and a muggy August. The goal isn't to stop that; it's to build near the middle of the swing so the wood moves a little each way instead of shrinking for good.

Pin vs pinless meters

Both types work. They measure different things, and knowing the difference is most of the skill.

Pin meters read electrical resistance between electrodes pushed into the wood. Their strength is depth: with insulated pins you choose exactly where in the board you're reading. They need species and temperature corrections.

Pinless meters read through the surface with an electric field, so they're fast and leave no holes, but the outer layers dominate the reading. On wood that's still drying, that's the driest part.

Neither reads high moisture well. The Wood Handbook treats anything above about 30 percent as qualitative, so a meter showing 45 on a green board is telling you "wet," not "45." Our guide to moisture meters on thick stock covers depths, corrections and reliable ranges in detail.

Reading thick slabs correctly

A thick slab dries from the outside in, so its moisture runs in a gradient: driest at the faces, wettest in the middle. A short-pin meter or a pinless pad reads the dry outer layer and can make a wet slab look ready.

For a number that represents the whole piece, the Wood Handbook's rule is pin depth of a fifth to a quarter of the thickness: roughly ⅝ to ¾ inch on a 3-inch slab. Compare a shallow reading with a deep one; a big gap means the core still has a way to go.

When it really matters, weigh. An oven-dried sample gives the true moisture content, and from it you can track a whole slab by its weight on a scale. The thick-stock meter guide walks through the arithmetic.

After the kiln: storing dry lumber

Kiln-dried wood starts taking moisture back the day it leaves the kiln. The Wood Handbook gives a sense of how fast: 1-inch hardwood dried to 8 percent or less and piled solid under a roof in warm, humid weather gained about 2 percent per month for the first 45 days, then about 1 percent a month through a humid season. In an open, roofed shed the gain was about 1 percent per month; in a closed shed, about 0.3 percent.

So:

  • Bring dried wood indoors, or into a closed, conditioned shop, as soon as you can.
  • Store it flat on supports, at least 6 inches off a concrete floor, as the Wood Handbook advises for finish lumber.
  • Wrap or cover it if it has to wait somewhere humid.
  • Check it with a meter before you mill it, especially after a summer in the garage.

If your shop is unheated, a few degrees of heat helps. The Wood Handbook shows that keeping a closed storage space warmer than the outside air lowers the humidity inside enough to hold wood near the target. See drying times for how long it takes to get there in the first place.

Join the Waitlist

If your boards are stuck at 12 to 14 percent, that's the gap a kiln closes. Put them on the list.

Join the Waitlist

HELP SHAPE THE PLANNED KILN

What wood would
you bring?

Share your species, thickness and board feet. We’ll email you before the kiln opens.

Join the Waitlist