COLUMBIA
KILN DRYING
Join the Waitlist

Status · November 15, 2026: planned, not installed. We are not accepting wood.

Calculating Board Feet for a Drying Load

One board foot is 144 cubic inches of wood, the same as a square foot of 1-inch-thick board. To count any piece: multiply length × width × thickness, all in inches, and divide by 144. With length in feet, it's length (ft) × width (in) × thickness (in) ÷ 12. For a whole stack, count one layer and multiply by the number of layers. Kilns price by the board foot, so this is the number that sets your bill.

Here's how to handle the awkward cases: tapered slabs, beams, and stacks you'd rather not take apart.

Boards

Formula: length (in) × width (in) × thickness (in) ÷ 144.

A board 10 feet long, 7 inches wide and 1 inch thick:

120 × 7 × 1 ÷ 144 = 5.83 board feet.

Twenty of them: 20 × 5.83 = 116.7 board feet.

Nominal vs actual thickness. Rough-sawn lumber is usually cut a little thick so it can shrink and still be planed to size. The USDA Forest Products Laboratory's air-drying study, for example, measured its 4/4 boards at 1⅛ inches and its 8/4 at 2³⁄₁₆ inches (FPL-GTR-121). That eighth of an inch matters on a big load: the same 10-foot, 7-inch board counted at 1⅛ inches is 120 × 7 × 1.125 ÷ 144 = 6.56 board feet, about 12 percent more. Ask any kiln whether it counts nominal or measured thickness.

Green vs dry. Wood shrinks as it dries, so a stack measured green contains slightly more board feet than the same stack after drying. Measure when you drop the wood off, and expect the kiln to do the same.

Slabs with a live edge

A slab's width varies along its length. Measure the width at the narrow end and the wide end (or at several points along a very irregular slab), average them, and use the average.

A slab 9 feet long, 19 inches wide at one end and 25 at the other, 2½ inches thick:

  • Average width: (19 + 25) ÷ 2 = 22 inches
  • 108 × 22 × 2.5 ÷ 144 = 41.25 board feet

Measure width across the flat face, not including bark that will come off. For a slab with a deep curve or a big void, take three or four width measurements and average them all.

Beams and timbers

Same formula. A handy shortcut: per foot of length, a beam has (width × thickness ÷ 12) board feet.

Beam size (inches) Board feet per foot of length
4 × 6 2.0
6 × 6 3.0
6 × 8 4.0
8 × 8 5.33
8 × 10 6.67

So an 8-foot 6x8 is 8 × 4 = 32 board feet, and an 8-foot 8x8 is 8 × 5.33 = 42.7 board feet. One cubic foot of solid wood is 12 board feet, which is a quick check on any of these.

A whole stack, by the layer

You don't have to measure every board. If the boards in a stack are the same thickness and length:

  1. Measure the length of the stack.
  2. In one layer, add up the widths of all the boards, leaving out the gaps between them.
  3. Calculate that layer as if it were one wide board.
  4. Multiply by the number of layers.

Example: a stack of 10-foot, 4/4 boards. One layer has boards adding up to 40 inches of wood across a 48-inch-wide stack, and the stack has 12 layers.

  • One layer: 120 × 40 × 1 ÷ 144 = 33.3 board feet
  • Twelve layers: 33.3 × 12 = 400 board feet

If board widths differ from layer to layer, measure two or three layers and use the average.

A whole stack, by volume

When you can't count layers, work from the outside dimensions and subtract the air.

The same stack, with ¾-inch stickers between layers, stands 12 × 1.75 = 21 inches tall. Its outside volume is 10 ft × 4 ft × 1.75 ft = 70 cubic feet. But only 1 inch of every 1.75 inches of height is wood, and only 40 of every 48 inches of width:

  • 70 × (1 ÷ 1.75) × (40 ÷ 48) = 33.3 cubic feet of wood
  • 33.3 × 12 = 400 board feet

Same answer. Leave out the stickers and the gaps and the volume method overcounts badly: 70 cubic feet × 12 would suggest 840 board feet, more than twice the real figure.

Common counting mistakes

  • Counting the air. Using a stack's outside dimensions without taking out stickers and gaps, as above, can double the count.
  • Mixing nominal and actual. Measure every piece the same way, and note which one you used.
  • Counting bark and wane. On slabs and slab-edged boards, measure the solid wood you'll keep, not the bark.
  • Rounding every board up. Round the total at the end, not each piece; on a few hundred boards, rounding each one adds up.
  • Forgetting the short pieces. Cutoffs and short boards in a stack still take kiln space and still count.

What the number means for drying

Cost. At the posted rates on our cost page, 400 board feet of 4/4 would run about 400 × $0.95 to 400 × $1.05, or $380 to $420, at other US kilns. Small loads hit minimum charges, posted at about $100 to $150.

Kiln space. Kilns are sized in board feet too. FPL's solar kiln design, for instance, holds 450 board feet of 4/4, and its sizing rule for solar kilns is a capacity of about 10 board feet per square foot of collector roof (FPL-GTR-118). A 400-board-foot stack would nearly fill one.

Mixed thicknesses. Count each thickness separately. Kilns price thick stock differently, and the 8/4 in a mixed stack will set the drying time for everything with it. See drying times.

Join the Waitlist

Put your board feet on the waitlist form, by thickness if you can. The form has a "help me estimate" link that uses these same formulas.

Join the Waitlist

HELP SHAPE THE PLANNED KILN

What wood would
you bring?

Share your species, thickness and board feet. We’ll email you before the kiln opens.

Join the Waitlist